A 3/4 inch SS304 welded mesh panel has nominal openings of 3/4 inch, equivalent to 19.05 mm, and is made by welding stainless steel wires at their intersections. The opening size alone does not define the panel: wire diameter, panel dimensions, edge finish, and manufacturing tolerances also affect suitability and cost. For a reliable quotation, specify whether 3/4 inch refers to the clear opening or the wire spacing, and provide your required wire diameter and panel size. This guide explains the key specifications and purchasing checks we recommend before placing a B2B order.
For more information, please visit our website.
This guide is intended for importers, distributors, fabricators, contractors, and industrial buyers evaluating 3/4 inch SS304 welded wire mesh panels. It is useful when you need to compare supplier quotations or convert a project requirement into a manufacturable specification. The information can also help purchasing teams identify missing details before requesting samples or production pricing. It is not a substitute for a project-specific engineering review where load, safety, or regulatory requirements apply.
Welded mesh consists of perpendicular wires joined at their crossing points. A 3/4 inch opening is nominally 19.05 mm, but suppliers may report opening size differently. A clear opening is measured between the inner faces of neighboring wires, while wire spacing or pitch is measured from the center of one wire to the center of the next. Because wire diameter changes the clear space, buyers should state which measurement they require.
SS304 identifies the specified stainless steel grade, while the mesh designation describes the opening arrangement. The designation does not specify wire diameter, panel size, surface finish, or dimensional tolerance. Those details should appear separately in the purchase specification. If a project calls for material traceability or particular inspection documents, state that requirement during quotation rather than assuming it is included.
For this product, the requested material is SS304 stainless steel. The appropriate grade depends on the panel’s environment, cleaning process, and contact with chemicals or other materials; buyers should evaluate these conditions with their technical team. A supplier may also discuss alternative stainless grades if the application warrants comparison, but a change in grade should be approved against the project specification. Do not treat “stainless steel” as a complete material description when grade identification matters.
Panels can differ in wire diameter, overall length and width, flat or otherwise specified edge condition, and surface appearance. The buyer should also clarify whether the panel is supplied as a standard sheet or requires cut-to-size production. As practical examples for quotation comparison, buyers may request prices for 2 mm and 3 mm wire options; these are examples, not a statement that either is suitable for every application or available as a standard specification.
A 3/4 inch opening may be considered for partitions, protective guards, general screening, equipment enclosures, or fabricated panels, provided the opening and wire dimensions meet the project’s requirements. The mesh can allow visibility and airflow while creating a physical barrier, but its suitability depends on the complete assembly and the hazards involved. For example, an opening that works for a general enclosure may not be appropriate where small objects, fingers, or specific particles must be contained. Confirm the required opening, load, and safety criteria before purchase.
For fabrication, consider how the panel will be cut, welded, fastened, or framed. Ask the supplier about edge condition and dimensional tolerance if the mesh must fit into a close-fitting frame. Where corrosion exposure is a concern, describe the actual environment—including cleaning agents, moisture, and outdoor exposure—so the material selection can be reviewed appropriately. SS304 should not be assumed to suit every chemical or marine environment without assessment.
If you are looking for more details, kindly visit Shunqiang Wire Mesh.
Write down the required opening and identify it as clear opening or pitch. Confirm whether the stated 3/4 inch dimension applies in both directions, and note any permitted tolerance. If the drawing uses metric units, include the metric target as well; 3/4 inch converts to 19.05 mm. This reduces the risk of comparing quotations based on different interpretations.
Provide the wire diameter, panel width, panel length, and required quantity. State whether the dimensions are finished dimensions or nominal dimensions before trimming. Include any requirements for cut edges, corners, flatness, surface finish, or additional fabrication. If these details are undecided, request options and compare them on the same basis.
Explain what the panel needs to do, rather than relying only on the product name. For a guard or enclosure, share relevant load, impact, or access requirements with your engineering team and supplier. For screening, clarify the size and type of material to be retained. A mesh opening and wire diameter by themselves do not establish a panel’s load capacity or safety performance.
Ask what documentation the supplier can provide for the ordered material and production specification. Depending on the project, this may include a dimensional inspection record or material documentation, but availability should be confirmed before ordering. Align the inspection method and acceptance criteria with the purchase order. This is especially important when multiple suppliers are being compared or the panel must match an existing assembly.
There is no single price for a 3/4 inch SS304 welded mesh panel because cost depends on the wire diameter, panel dimensions, order quantity, finish, cutting requirements, and packaging. Custom dimensions or additional processing can change the quotation compared with a standard panel. Minimum order quantity (MOQ) and production lead time also vary by specification and current production schedule. Request these terms directly from the supplier for the exact configuration you intend to buy.
For a useful quotation comparison, send every supplier the same drawing or specification sheet. Ask each to identify the opening definition, wire diameter, material grade, panel size, tolerance, MOQ, lead time, and delivery terms in the offer. If you are testing a new supplier, discuss whether a sample or trial quantity is possible and whether it will match production material and dimensions. Compare the total scope, not just the unit price.
Shunqiang Wire Mesh supports B2B buyers evaluating welded wire mesh panels by reviewing requested material, opening, wire diameter, dimensions, and order requirements for quotation. Share a drawing or written specification when available, and identify any unresolved details so that options can be discussed before production. For accurate pricing, include the destination and required delivery schedule along with quantity and panel configuration.
A 3/4 inch SS304 welded mesh panel is defined by more than its nominal opening: the measurement method, wire diameter, panel size, tolerances, finish, and application all matter. Start by confirming whether the 3/4 inch opening means 19.05 mm clear space or a center-to-center measurement, then specify the remaining dimensions and project conditions. Evaluate SS304 against the actual environment and do not infer load or safety performance from the mesh designation alone. For your next step, send Shunqiang Wire Mesh your drawing, quantity, delivery destination, and documentation needs to request a specification review and B2B quotation.
Contact us to discuss your requirements of 3/4 inch ss304 welded mesh panel. Our experienced sales team can help you identify the options that best suit your needs.